Vad är det för I/O på denna woofer ?

[Gäst]

Någon som vet vad det finns för ingångar/utgångar på denna sub ? http://www.thomann.de/se/samson_resolv_sub_120a_subwoofer.htm Har tänkt att koppla den med dessa monitorer http://www.thomann.de/se/behringer_ms40_multimedia_lautsprecher.htm

På mitt ljudkort har jag Tele 6.3 kontakter ut. På mina monitorer är det RCA kontakter. Men finns ingen bild på woofern så är det någon som vet vad för kontakter det finns på den ? Hur ska man koppla den ?

[Mr Keys]

Balanserad xlr, obalanserad rca ser det ut som när jag bildgooglar den....

[Leatherswine]

Så här ser baksidan ut: http://medias.audiofanzine.com/images/normal/samson-technologies-resolv-120a-416623.jpg

[Gäst]

Så här ser baksidan ut: http://medias.audiof...120a-416623.jpg

Okej Tack Hur ska den kopplas ?

[Leatherswine]

Här finns manualen: http://www.samsontech.com/site_media/legacy_docs/sub120a_OM_5L_v5_3.pdf

Klippte ut ett par stycken som borde vara nyttiga.

Men det verkar väl som att du helst ska koppla vidare till aktiva monitorer via "preamp level"-outputen, som ju också lämpligt nog är rca.

Operating the RESOLV 120a

12

The Ins and The Outs

The RESOLV 120a features both line

level and speaker level inputs and outputs so that connection with passive

or active satellites is easy. The PREAMP

LEVEL INPUTS simply pass the line

level signal through to the PREAMP

LEVEL OUTPUTS. You can use the line

inputs and outputs to interface the

RESOLV 120a with active monitors like

the Resolve 65a’s. The SPEAKER LEVEL

INPUTS can be connected from the

speaker outputs of a power amplifier,

and then the signal is sent from the

SPEAKER OUTPUTS, which are highpassed, to passive satellite speakers.

The following section details both

the line level and speaker level connections. The subsequent sections

detail the set-ups for many typical

configurations with both passive and

active monitors. In addition, there is a

detailed cable wiring diagram on page

16.

SPEAKER OUTPUT – The

SPEAKER OUTPUT connectors are

made via 5-way binding posts.

Use these connectors to connect from your external power amplifier speaker output. So, although the connector is

labeled FROM EXTERNAL AMPLIFIER SPEAKER OUTPUT, when using this configuration the connection here is used as

the input signal to the Resolv 120a.

SATELLITE SPEAKER - The SPEAKER OUTPUT connectors are 5-way binding posts. Connect here from your external

power amplifier. Use these connectors to connect to any passive satellite monitors like the Resolv 65’s.

INPUT (PREAMP LEVEL) – The left and right PREAMP INPUT connectors are made via standard RCA connectors.

They can be used to connect from any line level device such as a mixer.

OUTPUT (PREAMP LEVEL) – The left and right PREAMP OUTPUT connectors are made via standard RCA connectors.

They can be used to connect from any active studio monitors such as the Resolv 65a’s.

MUTE JACK – The MUTE jack provides a switch closure to activate Resolv 120a’s internal mute circuit. By using a

standard footswitch that you can buy at your local music store or by making a cable with a switch, or even by wiring

a switch permanently in the mix area, the Resolv120a can be easily turned on and off.

AC INLET – Connect the supplied IEC power cable here. Be sure that the power switch is in the off position when

connecting the AC cord.

Mono Sub With Active Satellites

If you have active studio monitors, installation is easy through the RESOLV 120a’s LINE LEVEL inputs and outputs. Below

is a typical system set-up using the RESOLV 120a with a mixer and a pair of active satellite speakers. The RESOLV 120a’s

inputs and outputs utilize industry standard RCA connectors. For a detailed wiring diagram, see the section “RESOLV

120a Connections” on page 19. Follow the steps in the diagram below to set up your system.

• Lower your mixer’s master outputs to all the way off.

• Connect the mixer’s left output to the RESOLV 120a’s LEFT LINE INPUT and the mixer’s right output to the RESOLV

120a’s RIGHT LINE INPUT. Now connect the RESOLV 120a’s LEFT LINE OUTPUT to the input of the left powered satellite, and the RESOLV 120a’s RIGHT LINE OUTPUT to the input of the right powered satellite.

• Now adjust the SWEEP control to the desired frequency. Consult your studio monitors owner’s manual for a recommended crossover point. You can also use your ears by adjusting the SWEEP control to the frequency that sounds

good to you. A good place to start is about 70 Hz.

• Now set the level of your active satellite speakers up to the normal operating level. Run an audio signal (like some

music from a CD) through your mixer and raise the level to a comfortable listening level. Now slowly raise the

RESOLV 120a VOLUME control and listen to the low frequency output. Adjust the RESOLV 120a to the level of low frequency output that you like. Now, when you raise and lower your mixer’s output, the RESOLV 120a and satellites will

track at the same relative volume.

[Mr Keys]

Så här ser baksidan ut: http://medias.audiofanzine.com/images/normal/samson-technologies-resolv-120a-416623.jpg

Happ, där ser man, jag fick nog fram en bild på nån annan sub. Så kan det gå. Ignorera mitt tidigare svar i sådana fall.

[Gäst]

Happ, där ser man, jag fick nog fram en bild på nån annan sub. Så kan det gå. Ignorera mitt tidigare svar i sådana fall.

Sånt som händer. Men vad menas och vart är den där preamp kontakten ? Kan inte hitta dehn.

[mickestrang]

http://www.thomann.de/se/prod_bdb_AR_162467.html?image=2

Länken du själv angav på Thomann har svaren